Bang-Bang控制方式旋转导弹气动特性数值分析

为研究Bang-Bang控制式鸭舵对旋转导弹气动特性的影响,在CFD软件中采用嵌套网格方法模拟导弹的旋转和鸭舵的偏转,对Bang-Bang控制式旋转导弹在不同攻角、马赫数和转速下的气动特性进行了数值模拟,得到了气动特性变化规律。研究表明,因鸭舵洗流方向的改变,耦合导弹自旋会导致弹体和尾翼的侧向力发生突变。通过与不控鸭舵的旋转导弹进行对比,采用Bang-Bang控制式鸭舵的旋转导弹的周期平均侧向力系数变小,周期平均法向力系数变大。由于侧向力的存在,导弹在一个周期内的合力会偏离竖直方向,合力偏离竖直方向的角度随着马赫数、自旋速率和攻角的增大而减小。     

Influence of propagation direction on operation performance of rotating detonation combustor with turbine guide vane

Due to the pressure gain combustion characteristics, the rotating detonation combustor (RDC) can enhance thermodynamic cycle efficiency. Therefore, the performance of gas-turbine engine can be further improved with this combustion technology. In the present study, the RDC operation performance with a turbine guide vane (TGV) is experimentally investigated. Hydrogen and air are used as propellants while hydrogen and air mass flow rate are about 16.1 g/s and 500 g/s and the equivalence ratio is about 1.0. A pre-detonator is used to ignite the mixture. High-frequency dynamic pressure transducers and silicon pressure sensors are employed to measure pressure oscillations and static pressure in the combustion chamber. The experimental results show that the steady propagation of rotating detonation wave (RDW) is observed in the combustion chamber and the mean propagation velocity is above 1650 m/s, reaching over 84% of theoretical Chapman-Jouguet detonation velocity. Clockwise and counterclockwise propagation directions of RDW are obtained. For clockwise propagation direction, the static pressure is about 15% higher in the combustor compared with counterclockwise propagation direction, but the RDW dominant frequency is lower. When the oblique shock wave propagates across the TGV, the pressure oscillations reduces significantly. In addition, as the detonation products flow through the TGV, the static pressure drops up to 32% and 43% for clockwise and counterclockwise propagation process respectively.     

基于阶次跟踪的旋转机械启动过程振动分析

旋转机械运转时其旋转部件产生的振动和噪声所表现出的特征和轴的转速有密切关系。在这类故障的特征分析中,使用阶次跟踪分析法比一般的频域分析更具有优势。对2种典型的阶次跟踪法进行了论述,在此基础上用2个仿真信号对旋转机械启动过程进行了模拟分析,并得到了比较理想的结果。     

具有连续反馈的在线草图符号识别算法

当前多数在线草图符号识别方法是在用户绘制完图形后,通过点击按钮或等待一定时间来反馈识别结果。为提供连续反馈,提出了一种基于图元的部分草图识别算法:对输入笔画进行笔画分割得到图元表示,提取表示两个图元空间关系的新特征,依据指派问题模型,通过该特征的相似度识别符号。算法简单,无须训练,而且与笔顺、笔画数和图形大小无关。实验证明了方法的有效性。     

不同转位方案下双轴旋转惯导系统精对准分析

针对双轴旋转惯导系统转位方案的设计和选择问题,提出了3种合理的转位方案:16次序、24次序和32次序,建立了旋转惯导系统的误差方程和卡尔曼滤波模型.观测量取速度误差和位置误差时,分别对3种转位方案下精对准过程进行了分析仿真.结果表明,24次序转位方案精对准过程所需时间最短,精度最高,其次是32次序,16次序转位方案精对准过程所需时间最长,精度最低.     

Cell-type continuous electromagnetic radiation system generating millimeter waves for active denial system applications

The cell-type continuous electromagnetic radiation system is a demonstration device capable of generating high-power millimeter electromagnetic waves of a specific wavelength and observing their effects on living organisms. It irradiates a biological sample placed in a 30 × 30 × 50 cm³ cell with electromagnetic waves in the 3.15-mm-wavelength region (with an output of ≥1 W) and analyzes the temperature change of the sample. A vacuum electronic device-based coupled-cavity backward-wave oscillator converts the electron energy of the electron beam into radiofrequency (RF) energy and radiates it to the target through an antenna, increasing the temperature through the absorption of RF energy in the skin. The system causes pain and ultimately reduces combat power. A cell-type continuous electromagnetic radiation system consisting of four parts—an electromagnetic-wave generator, a high-voltage power supply, a test cell, and a system controller—generates an RF signal of ≥1 W in a continuous waveform at a 95-GHz center frequency, as well as a chemical solution with a dielectric constant similar to that of the skin of a living organism. An increase of 5 °C lasting approximately 10 s was confirmed through an experiment.     

玄武岩纤维增强塑料筋耐海水腐蚀性研究

海工工程中由于海水的腐蚀,混凝土中的钢筋会出现锈蚀等问题.玄武岩纤维增强塑料筋作为一种新型建筑材料,用来代替钢筋用在海工工程等腐蚀性较强的混凝土中,以此避免钢筋锈蚀带来的耐久性问题.研究了玄武岩纤维增强塑料筋耐海水腐蚀性,采用常温长期浸泡和高温浸泡加速腐蚀试验方法,得出玄武岩纤维增强塑料筋在常温下耐海水腐蚀性较强,而在...     

不同填料旋转床功耗与气体压降特性对比研究

采用同心环波纹碟片填料和不锈钢波纹丝网两种填料,在气液逆流CO2吸收操作时,对旋转床的功耗及气体压降进行了对比实验分析。功耗特性对比结果表明,当液流量不变,旋转床转速低于38 rad/s时,丝网填料旋转床吸收器消耗的功率大于碟片填料旋转床吸收器消耗的功率;转速高于38 rad/s时则相反。气体压降特性对比结果表明,在液流量和旋转床转速不变的操作条件下,碟片填料旋转床的气体压降要大于丝网填料旋转床的气体压降约50 Pa;在气流量和转速不变的操作条件下,当液流量较小时,丝网填料旋转床的气体压降大于碟片填料旋转床的气体压降;当液流量较大时则相反。在相同气流量和液流量下,碟片旋转床气体压降要大于丝网填料旋转床气体压降。研究结果为AIP系统旋转床吸收器的填料优选及全系统的优化设计提供了重要的依据。     

An application of yield management for Internet Service Providers

In this paper we study strategies for better utilizing the network capacity of Internet Service Providers (ISPs) when they are faced with stochastic and dynamic arrivals and departures of customers attempting to log‐on or log‐off, respectively. We propose a method in which, depending on the number of modems available, and the arrival and departure rates of different classes of customers, a decision is made whether to accept or reject a log‐on request. The problem is formulated as a continuous time Markov Decision Process for which optimal policies can be readily derived using techniques such as value iteration. This decision maximizes the discounted value to ISPs while improving service levels for higher class customers. The methodology is similar to yield management techniques successfully used in airlines, hotels, etc. However, there are sufficient differences, such as no predefined time horizon or reservations, that make this model interesting to pursue and challenging. This work was completed in collaboration with one of the largest ISPs in Connecticut. The problem is topical, and approaches such as those proposed here are sought by users. © 2001 John Wiley & Sons, Inc., Naval Research Logistics 48:348–362, 2001     

M739引信头部触发机构发火模式与判别方法研究

针对M739引信头部机构的基本结构与特性,分析其头部触发机构的发火原理,提出发火模式种类的判别方法。结合某型引信的具体参数,计算其对钢板、胶合板和地面三种不同目标介质射击时的碰击力,分析碰击力、防雨机构静态下移抗力及支筒图定抗力对发火模式的影响。试验结果表明,该发火模式判别方法适用于M739系列引信。